Project Information

Bid Title

ITB2026-107 South Annex Building Repairs

Issuing Agency

City of Tybee Island

Location

Georgia

Published Date

Apr 10, 2026

Closing Date

May 12, 2026

Government Level

State & Local

Status

Closed

Ref. #

ITB2026-107

Original Source

Join to Access Full Details

Bid Inquiries

Join to Access Full Details

Bid Documents

Join to Access Full Details

Project Description

Bid Number:	ITB2026-107
Bid Title:	ITB2026-107 South Annex Building Repairs
Category:	Open RFPs
Status:	Open

Description: The City of Tybee Island, GA will be accepting bids for the South Annex Building Repairs. BIDS MUST BE SUBMITTED BY 2:00 PM ON TUESDAY, MAY 5, 2026, to Aleesha Robinson, at Tybee Island City Hall, 403 Butler Avenue, Tybee Island, GA 31328. A PRE-BID MEETING will be held 1:00PM, TUESDAY, APRIL 21, 2026, at the Public Safety Building Conference Room (78 Van Horne) all prospective bidders are strongly encouraged to attend. Direct all questions in writing to Aleesha Robinson at For security reasons, you must enable JavaScript to view this E-mail address. The City of Tybee Island, GA may (i) reject any, any part of, or all bids and proposals with any party submitting a bid or proposal, or (ii) waive informalities and technicalities, (iii) negotiate directly with any party submitting a bid or proposal, or (iv) accept that proposal which the City of Tybee Island, GA deems to be in its best interest, whether or not it is the lowest dollar proposal. Publication Date/Time: 4/10/2026 12:00 AM Closing Date/Time: 5/12/2026 11:59 PM Related Documents: ITB 2026-107 South Annex Building Repairs

Attachment Preview

ITB NO. 2026-107

SOUTH ANNEX BUILDING REPAIRS

BID DUE: TUESDAY MAY 5, 2026 at 2:00pm

PRE-BID MEETING: TUESDAY APRIL 21, 2026 at 1:00 pm

CITY OF TYBEE ISLAND, GEORGIA

BRIAN WEST, MAYOR

MICHAEL “SPEC” HOSTI, MAYOR PRO TEM

TONY PLOUGH

NICK SEARS

CAMERON JACKSON

KATHRYN WILLIAMS

NICK HALE

DOCUMENT CHECK LIST

The following documents are contained in and made a part of this Invitation to Bid or are required

to be submitted with the bid. It is the responsibility of the Bidder to read, complete and sign, where

indicated, and return these documents with his/her bid. FAILURE TO DO SO MAY BE CAUSE

FOR DISQUALIFICATION OF THE BIDDER.

INTRODUCTION

SPECIFICATIONS AND REQUIREMENTS

INSTRUCTIONS TO BIDDERS

GENERAL INFORMATION

SURETY REQUIREMENTS

ATTACHMENTS: A. SIGNATURE SHEET; B. CONTRACTOR AFFIDAVIT; C.

SUBCONTRACTOR AFFIDAVIT; D. SAVE AFFIDAVIT; E. W-9/VENDOR

INFORMATION; F. DEBARMENT CERTIFICATION; G. BID SHEET; H. CHECKLIST

INTRODUCTION

This is an invitation to bid to supply the City of Tybee Island, Georgia (sometimes hereinafter

referred to as “Owner”) with products or services as indicated herein.

Sealed bids must be received by 2:00pm local time, on Tuesday May 5, 2026. The City of

Tybee Island reserves the right to reject any or all bids.

A pre-bid meeting will be held on Tuesday April 21, 2026, at 1:00 pm in the Public Safety

Building conference room (78 Van Horne Avenue, Tybee Island). Interested bidders are

encouraged to attend, as they will have the opportunity to discuss specifications and ask

questions.

METHOD OF AWARD: If the City of Tybee Island awards a contract from this ITB, it will be

awarded to the responsible bidder with the lowest responsive bid. Bidders must respond

completely by filling in all applicable blanks. Bids are subject to the terms and conditions of this

Invitation to Bid.

Signature of bidder indicates understanding and compliance with attached terms and conditions

and all other specifications made a part of this ITB, and any subsequent award or contract. All

terms, conditions and representations made within this ITB will become an integral part of the

contract. Nothing contained within this ITB is indicative of intent by the City of Tybee Island to

reimburse the bidder, in whole or in part, for any costs associated with preparation, submission, or

presentation of bids.

Instructions for preparation and submission of a bid are contained in this ITB package. Please note

that specific forms for submission of a bid are required.

The City of Tybee Island has an equal opportunity purchasing policy to assure all procurement

procedures are conducted in a manner that provides maximum open and free competition. The City

seeks to ensure that all segments of the business community have access to supplying the goods

and services needed by the City. The City provides equal opportunity for all businesses and does

not discriminate against any persons or businesses regardless of race, color, religion, age, sex,

national origin or handicap.

The City is seeking a bid package for service or materials equal to or exceeding specifications set

forth on the attached pages. Bidders not meeting these standards will be rejected. The attached

specifications become and remain a part of this ITB.

All responses, inquiries, or correspondence relating to, or in reference to, this ITB, and all reports,

charts, displays, schedules, exhibits and other documentation by the bidders will become the

property of the City when received. The City retains the right to use any or all ideas presented in

any response to this ITB, whether amended or not. Selection or rejection of the bid does not affect

this right.

BACKGROUND AND SCOPE OF SERVICES:

The City of Tybee Island seeks qualified bidders for the building repairs listed below in the Scope

of Services at the South Annex Building, located at 1509 Strand Avenue, Tybee Island, Ga, 31328,

which is owned by the Citty of Tybee Island.

SCOPE OF SERVICES:

WORK UNIT A: THERMOPLASTIC POLYOLEFIN (TPO) MEMBRANE ROOF

SECTION

The CONTRACTOR will mobilize all necessary equipment required to remove and replace

approximately 1,300 square feet of a TPO roof section. The work shall include the following:

• Removal and disposal of all existing roof details.

• Removal and disposal of all existing eave trim, wall caps, termination bar, and all flashings.

• Removal and disposal of all debris in preparation for the new roof installation.

• The CONTRACTOR will inspect the decking. All bad decking will be replaced with a

similar type and thickness. The bid will include up to five (5) 4’ x8’ sheets of one of the

following types of plywood: CDX Plywood, OSB Sheathing, or Pressure Treated

Plywood. If additional sheets are required, they will be paid for as an extra.

• Furnish and install 1-inch rigid ISO board over the entire roof section. The ISO section

will be mechanically fastened to the roof deck using screws and 3-inch metal or plastic

plates, with a minimum of six (6) fasteners per each 4’ x 8’ board.

• Fabricate and install crickets around all skylights and curbed roof accessories to redirect

water around rooftop penetrations. A 2-inch minimum incline on the crickets will be

required.

• Furnish and install Carlisle White 60-mil TPO membrane on all roof surfaces and

mechanically fasten.

• Furnish and install White 60 -mil TPO to all vertical details of the roof. They will include

curbs and walls. The TPO membrane shall be fully adhered to the vertical surfaces.

• The CONTRACTOR will lift all existing equipment on roof as needed to install the roof

components underneath. Once roof is installed the CONTRACTOR will reset all

equipment of the roof and refasten as necessary.

• Furnish and install new TPO molded pipe flashings.

• The CONTRACTOR will wrap and seal all pitch pockets and equipment lines with

unsupported TPO. A pourable sealant will be used to provide a total, watertight rubber

seal on all pitch pockets.

• Furnish and install all new aluminum end caps. The color will be determined at a later

date.

• Furnish and install TPO caulk as needed.

• Upon completion the CONTRACTOR will probe all seams to ensure that no cold welds

exist and apply target patches if any are found.

• The CONTRACTOR shall provide a No Dollar Limit for a period of twenty (20) years

from the date of substantial completion. This warranty shall include the following:

membrane roofing, base flashings, fasteners, edge metal roofing accessories, and other

components of the membrane roofing system.

•

WORK UNIT B: ALUMINUM STANDING SEAM ROOF SECTION

The CONTRACTOR will mobilize all necessary equipment required to remove and replace

approximately 1,600 square feet of an Aluminum Standing Seam Roof section. The work shall

include the following:

• Removal and disposal of all shingles and underlayment.

• The CONTRACTOR shall inspect the decking after shingle removal. All bad decking will

be replaced with a similar type and thickness. The bid will include up to five (5) 4’ x8’

sheets of one of the following types of plywood: CDX Plywood, OSB Sheathing, or

Pressure Treated Plywood. If additional sheets are required, they will be paid for as an

extra.

• The CONTRCTOR shall furnish and install an SBS modified self-adhesive membrane with

non-woven fiberglass over all solid deck surfaces. Mid-States High-Temperature Ice and

Water Shield or approved equal is required.

• The CONTRACTOR shall fabricate and install all flashing required to ensure a watertight

roof system.

• The CONTRACTOR shall fabricate and install a curb for exhaust vents and all roof vents.

• The CONTRACTOR shall furnish and install new metal roof pipe boots and gas vents and

paint all unfinished surfaces to match roof as best as possible.

• The CONTRACTOR shall furnish and install .032 aluminum standing seam roof system

with a painted finish. The style, width of panel, and color is to be determined prior to

ordering materials.

• The CONTRACTOR shall clean up all related construction debris and sweep around the

property with magnets for nails and metal trimmings.

• The CONTRACTOR shall provide a No Dollar Limit for a period of five (5) years from

the date of substantial completion. This warranty shall include the following: membrane

roofing, base flashings, fasteners, edge metal roofing accessories, and other components of

the membrane roofing system.

WORK UNIT C: COLLECTION BOXES AND 6-INCH ALUMINUM BOX GUTTERS

The CONTRACTOR will mobilize all necessary equipment required to furnish and install

approximately 160 linear feet of 6-inch box gutters, two (2) downspouts, and 65 linear feet of

buried 6-inch storm sewer with a connection to an existing storm drain inlet. The work shall

include the following:

• Furnish and install 6-inch box gutters, made from .032 aluminum or24 gauge steel.

• The CONTRACTOR shall secure the box gutters with high strength, corrosion resistant

materials (stainless steel or galvanized) pancake screws at 12 inches on center. Structural

straps or brackets will be installed at every 3 feet.

• Furnish and install three (3) box gutter downspouts. One at the northwest corner of the

building and this will discharge at grade. One downspout will be installed at the southwest

corner and another one will be installed at the southeast corner of the building. These two

downspouts will discharge into a 6-inch buried PVC storm sewer pipe that will be installed

as part of this contract.

• The CONTRACTOR will install a 60inch storm sewer along the south side of the building

underneath the paver walkway. The CONTRACTOR will remove the pavers and either

trench or excavate a trench to install approximately 65 linear feet of 6-inch storm sewer.

Once pipe is installed CONTRACTOR will backfill with sand and reset the paver blocks

in the walkway. The 6-inch storm sewer will then be cored into the existing box inlet

located in the parking lot at the southeast corner of the building.

• The Contractor shall provide a five (5) year warranty on all component of the gutter system.

WORK UNIT D: PVC FACIA BOARDS

The CONTRACTOR will mobilize all necessary equipment required to furnish and install

approximately 210 linear feet of PVC facia boards. The work shall include the following:

• Furnish and install PVC facia boards along all edges of the building.

• The CONTRACTOR shall secure the facia boards using 3-inch, corrosion resistant nails to

prevent rust streaks. Use at least two (2) fasteners per rafter, placed about 1-2 inches from

the top and bottom edges.

• The CONTRACTOR shall use exterior grade caulk to seal any gaps at joints.

WORK UNIT E: HARDIE SIDING, PLYWOOD, AND SYNTHETIC WEATHER

BARRIER

The CONTRACTOR will mobilize all necessary equipment required to furnish and install

approximately 320 square feet of new 3/4-inch plywood and Hardie siding at two locations, one

on the west side and one on the east side above the main entrance to the building. The work shall

include the following:

• Furnish and install ¾-inch CDX Plywood, OSB Sheathing, or Pressure Treated Plywood

along a section of the west side of the building and a section on the east side of the building

above the main entrance.

• Furnish and install a heavy-duty synthetic weather barrier between the ¾-inch plywood

and Hardie board siding.

• Furnish and install Hardie siding over the newly installed plywood.

• The CONTRACTOR shall fasten the Hardie siding using 6d or 8d corrosion resistant siding

nails or equivalent corrosion resistant screws. Fasteners should be no closer than 2-inches

from panel corners.

• The Hardie siding shall be fastened to intermediate studs at 12-inches or 16-incheson

center.

1. INSTRUCTIONS TO BIDDERS

Purpose: The purpose of this document is to provide general and specific information for use in

submitting a bid to supply the City of Tybee Island with equipment, supplies, and/or services as

described herein. All ITBs are governed by the Code of the City of Tybee Island, Georgia, 15-

2015 Sec 1, Art VII, Procurement, Sec 2-400, and the laws of the State of Georgia.

Bidders must carefully review all provisions of, and attachments to, this document prior to

submission. Each bid constitutes an offer and cannot be withdrawn except as provided herein. This

ITB and any attachments, plans, and/or other related documents can be found on the City’s website

at https://www.cityoftybee.org/Bids.aspx. It is incumbent upon the bidder to check the website

for additional information and/or addendums.

1.1 How to Prepare Bids:

All Bids must be:

a. Prepared on the forms enclosed herewith, unless otherwise prescribed, and all

documents must be submitted.

b. Bids must be signed by the business owner or authorized representative, with all

erasures or corrections initialed and dated by the official signing the Bid. ALL

SIGNATURE SPACES MUST BE SIGNED.

1.2 How to Submit Bids:

One original, and one electronic copy (usb flash drive) must be submitted in a sealed

opaque envelope, plainly marked with the ITB number and title, and bidder’s company

name, to the office of the address below prior to the time specified. Include all required

attachments, which can be found at the end of this document.

• Include all requested documents, in addition to a W-9 and certificate of

insurance, and required bid bond.

• City/County Occupational Tax Certificate Requirement: Contractor must

supply a copy of their Occupational Tax Certificate as proof of payment of the

occupational tax where their office is located. In addition, if a contract is

awarded, contractors that are not located on Tybee Island are required to

obtain a Tybee Island contractor registration. Contact Aleesha Robinson for

additional information, at (912)472-5072, or in person at Tybee Island City

Hall 403 Butler Ave, Tybee Island, Ga

• All Bids must be hand delivered, mailed, or sent by courier in sufficient time

to ensure receipt by the Purchasing Agent on or before the time and date

specified above.

Commodity Codes

• NAICS 236220Commercial and Institutional Building Construction

* Disclaimer: Government BidHub provides information on bids, RFPs (Requests for Proposals), and RFQs (Requests for Qualifications) solely for convenience and informational purposes. This site is not an official public notice board. For official details, responses, or inquiries, please contact the relevant government agency directly.